Pricing About Free Downloadfor Windows 8.1 / 10 / 11

Frequently Asked Questions

Answers to the most common questions about ZofzPCB

No answer found for "". Ask us: support@check-pcb.com

Contact page →

Getting started

Q1 Is the Gerber viewer really free?

Yes. The complete 3D workflow (loading, 3D view, navigation, measurement) is free forever, not a trial. You only need a free license key, sent by email. The STEP Export plugin for specific workflows is optional.

The free version includes the full 3D viewer, all file formats, automatic 3D component modeling, measurement tools, component and net navigation, and the programmatic interface. New installations include the STEP Export plugin free for 30 days.

Compare the free version and the STEP Export plugin →
Q2 Which files do I need?

Your Gerber layers and drill files, from any CAD tool. For 3D components, add the IPC-356 netlist and optionally a BOM. Or simply use a single ODB++ or IPC-2581 file, which already contains everything.

Quick-start Guide →Supported file formats in the User Manual →
Q3 Does it work with my CAD tool?

Very likely. ZofzPCB reads standard Gerber (RS-274X), drill and IPC-356 files from any CAD tool, as well as ODB++ and IPC-2581. It's tested with KiCad, Altium Designer, Eagle, Protel and Zuken.

How to export the IPC-356 netlist →
Q4 Does ZofzPCB run on Mac or Linux?

ZofzPCB runs on Windows 8.1, 10 and 11 (64-bit). There's no Mac or Linux version.

Also needed: Microsoft VC++ Runtime (download link on the download page), DirectX 11 and a scroll wheel mouse. An integrated GPU is enough for small and medium boards; a dedicated gaming GPU is recommended for large boards.

System requirements in the User Manual →
Q5 Why view Gerbers in 3D?

A 3D view shows your board as it will be built: layers in order, vias in place, components on top. That reveals errors a flat 2D view hides. It has a few drawbacks too, and we explain them openly.

Why view your Gerbers in 3D? →
Q6 How do I install ZofzPCB and activate my license?

Download and run the installer. Two license types:

Free licenseRequest your free key on the download page. Enter it under Help → Enter License Key.
Plugin licensePurchase on the pricing page. You receive a key by email. Enter it under Help → Enter License Key.
Get your free license key →
Q7 My browser or antivirus warns about the download. Is it safe?

Yes. The installer and the program are code-signed. A new release can trigger a SmartScreen warning for a short time until it has built up reputation. If your antivirus flags a file, write to support@check-pcb.com.

Loading and stackup

Q8 Can I view ODB++ files in 3D?

Yes. Open your ODB++ archive (.tgz or .tar) via File → Open → ODB++, and ZofzPCB shows the complete board in 3D, components included, because ODB++ already contains the netlist and component data.

ODB++ viewer →
Q9 Why does ZofzPCB not recognize my Gerber files automatically?

The autoloader identifies files by name and extension. Move all Gerber files into a single folder before loading. Eagle users: Eagle’s default export creates multiple subdirectories: move files into one folder first.

Updates keep your own rules. Reset Rules restores the rules that ship with ZofzPCB.

Auto Load in the User Manual →
Q10 What does the “Drill / Pad Fit Warning” mean?

Only a few drill holes matched pads. Many drill files are exported with an offset, so ZofzPCB applies Auto-Offset by default. If your files are exported correctly, turn it off: right-click Drill Plates and choose Setup Excellon Format.

Auto-Offset in the User Manual →
Q11 My layers are in the wrong order after autoloading: how do I fix this?

Open the stackup editor and drag layers into the correct order: top copper at top, bottom copper at bottom. Save as a .camset file so ZofzPCB remembers the correct order next time.

Reviewing the stackup in the User Manual →
Q12 What stackup information do I need to enter manually, and why?

Gerber files carry copper artwork but not stackup parameters. ZofzPCB makes a smart suggestion. Review and complete:

  • Layer type: whether each dielectric layer is a core or pre-preg
  • Dielectric thickness: thickness of each layer in millimeters
  • Copper weight: typically 1oz, 2oz, or 0.5oz per copper layer
  • Material: FR4, Rogers, polyimide, or other

For 3D visualization, basic layer order is sufficient. For DFM validation, a complete stackup is essential.

Layer types and thickness in the User Manual →
Q13 How do I save my stackup settings so I don’t have to re-enter them next time?

Save as a .camset file via File → Save As. This saves all settings but not the rendered board. Load via File → Open to re-read Gerber files with saved settings. For a complete saved state use .zofzproj.

Saving your stackup in the User Manual →
Q14 Can ZofzPCB handle blind and buried vias?

Yes. µVias, blind vias, and buried vias are all supported. The drill files must specify which layers each via spans. If vias aren’t rendering correctly, check that drill files correctly assign via type and layer span.

Drill plates and via types in the User Manual →
Q15 My board outline is missing or wrong. What can I do?

ZofzPCB builds the board shape from the board outline layer. Most problems have one of three causes: the outline is drawn on a copper or silkscreen layer instead of its own layer, the outline drawing isn't a closed loop, or text and drawings outside the board are mistaken for board parts. In the stackup dialog, right-click the layer name to choose how the outline is identified (for example, “Take the greatest loop”), or to use an outline drawn on another layer. More details: User Manual 2.4 Board outline.

3D visualization and navigation

Q16 Where do the 3D components come from?

From the IPC-356 netlist your CAD tool already exports. It contains every footprint, and ZofzPCB turns them into 3D models automatically, for free.

How it works →
Q17 Why are my components not showing in the 3D view?

Components require a BOM file and IPC-356 netlist. If either is missing, no component models are placed. Also check that component references in the BOM match those in the netlist: IPC-356 truncates references to 6 characters, which can cause mismatches.

IPC-356 and BOM matching in the User Manual →Background: IPC-356 and 3D components →
Q18 How do I export a netlist from my CAD tool?
CAD toolExport path
EagleFile → Export → IPC
KiCadFile → Fabrication Outputs → IPC-D-356 Netlist File
Altium DesignerFollow Altium’s export documentation for IPC-356 output
Protel 99seTools → CAM Wizard → Test Points → IPC-D-356A

Note: IPC-356 limits reference names to 6 characters. Longer references are truncated.

IPC-356 and BOM matching in the User Manual →Background: IPC-356 and 3D components →
Q19 How do I cut a cross-section through my board?

Point at the place where you want to cut. Hold Delete and move the mouse to set the angle of the cut; it snaps in 45° steps, or hold Shift as well for any angle. Then release. Hold Delete again and move the mouse to move the cut through the board. Press Escape to leave the cross-section and return to the full board view. Alternatively, right-click and choose Set Measurement Target → Cross-cut.

Cross-section in the User Manual →
Q20 Zooming is too fast close to the board. Can I slow it down?

Yes. Hold Ctrl while you turn the mouse wheel to zoom more slowly, or Shift to zoom faster. This also works with the numeric keypad. All mouse and keyboard controls are under Help → Mouse & Keyboard.

Q21 How do I get the total number of pads or drill holes?

Pads: File → Export → Netlist CSV writes one line per pad, so the number of lines minus one is your pad count. Drill holes: open the Holes List and select a tool; the status bar shows the count for that tool and for all holes.

Netlist CSV export in the User Manual →
Q22 The 3D view is slow or stuttering: how do I improve performance?

Lower SubSampling (View menu): biggest single impact. Turn off unused layers in the right panel. On laptops, assign ZofzPCB to the dedicated GPU in Windows Settings → Display → Graphics. Update graphics drivers.

Performance and GPU in the User Manual →
Q23 Can I use ZofzPCB without a dedicated GPU?

Yes. For small to medium boards, integrated GPU is sufficient. For large/complex boards, a dedicated GPU is recommended. DirectX 11 is required.

System requirements in the User Manual →

STEP Export plugin

Q24 What is the difference between the free version and the STEP Export plugin?

The free version gives the complete 3D validation workflow with no time limit, including Body Builder for exact component models and View-Only Mode for sharing secure 3D views. The STEP Export plugin adds:

  • STEP Export: STEP export for mechanical CAD, thermal simulation and electromagnetic simulation
  • Compare Designs: Color-coded 3D diff between two board versions

The STEP Export plugin is available as a 1-year or perpetual license: €99 per year or €299 once, plus VAT. A 1-year license ends after 12 months; there is no automatic renewal.

Full feature comparison on the Pricing page →
Q25 Can I export my board to STEP for mechanical CAD?

Yes, with the STEP Export plugin: the complete board, including all components, as a STEP assembly for SolidWorks, Fusion 360, FreeCAD and other MCAD tools, and as detailed models for thermal and electromagnetic simulation. €99 per year or €299 once, free for 30 days.

To export, go to File → Export → STEP. The file includes the board outline, all copper layers and every mounted component as a structured assembly, and also works with CATIA and any other STEP-compatible tool.

How STEP export works →STEP file export in the User Manual →
Q26 Can I import my own STEP models for components?

No, ZofzPCB doesn't import STEP models. Build the components in ZofzPCB (automatic models, plus Body Builder for special parts), export the board with the STEP Export plugin and add your own models in your mechanical CAD tool.

Q27 Can I compare two revisions of my board?

Yes, with the STEP Export plugin: load both revisions, and every added trace, removed part and moved pad is highlighted in 3D, on every layer. Free for 30 days.

Load your board, then File → Compare and choose the two versions, ideally saved as .zofzproj.

Compare Designs →Compare revisions in the User Manual →
Q28 Can I share my board in 3D without sending my Gerbers?

Yes, for free: save it in View-Only Mode, and others open the encrypted 3D model in the free ZofzPCB. They can rotate and inspect it, but not edit it or extract manufacturing data.

To create one, go to File → Save As → .zofzproj and check View-⁠Only Mode. Creating and viewing the file are both free.

View-Only Mode →View-only sharing in the User Manual →
Q29 What is the Body Builder and when do I need it?

A geometric editor for creating precise custom 3D models for components the auto-modeler cannot capture: exotic parts, non-standard housings, components where exact geometry matters for mechanical checks or STEP export. Models are saved to your component library and reusable across boards. Body Builder is part of the free version.

Body Builder in the User Manual →

Licenses and purchasing

Now What is temporarily unavailable?

Downloads still work. The free license key is temporarily unavailable.

The links to 2Checkout and DigiKey are temporarily disabled.

Q30 What happens when my 30-day plugin trial ends?

ZofzPCB continues as the free version, with nothing to cancel. The STEP Export plugin then needs a license, from €99 per year.

Smart Import, 3D Visualization, Board Navigation, Precise Measurement, Body Builder and View-Only Mode stay free, with no time limit, and your projects stay on your computer.

See pricing →
Q31 Yearly or perpetual?

A 1-year license ends after 12 months; there is no automatic renewal. A perpetual license is paid once and includes all updates and bug fixes, with no time limit.

License terms (EULA) →
Q32 How can I buy the STEP Export plugin?

Online on the Pricing page (our reseller 2Checkout handles the payment, including PayPal), through DigiKey (1-year or perpetual licenses), or by bank transfer for volume orders.

Volume and B2B licensing →
Q33 Is there a refund?

Yes. Contact support@check-pcb.com within 14 days of your purchase with your order number, and we will arrange a full refund.

Refund & Withdrawal Policy →
Q34 I have a Premium license. What happens now?

Your license now covers the STEP Export plugin. A perpetual Premium license includes all future updates. A 1-year Premium license is valid until it ends.

Q35 Can I move my license to a new computer?

Yes. One license key covers one installation, and you can move it to a new computer once per month.

License terms (EULA) →
Q36 I lost my license key. What can I do?

Open the license page, enter the email address you used and click “Resend My Key”.

Q37 Is there an online version? Are my files uploaded?

No, and that's deliberate. ZofzPCB is a Windows application that opens your design locally. Your Gerber and design files never leave your computer.

Privacy Policy →
Q38 What data does ZofzPCB send to your servers?

Only what is needed for license activation and update checks: your license key, a device identifier, your IP address and the installed version. Your design files never leave your computer, and ZofzPCB sends no crash reports or usage statistics. Details are in our Privacy Policy.

Still unsure? Try it on your own board.

Free Downloadfor Windows 8.1 / 10 / 11

Includes the STEP Export plugin free for 30 days. Free version forever after. No credit card required.

Questions? Contact us →